![]() ![]() The fact that I can even think of plaster of Paris when considering working on paper is an indication of a new level of freedom I’ve reach in my creative process because of this mixture. Since I didn’t have a plan that made the thickness of the paper a deal breaker, I knew I could beef it up a bit with the plaster + gesso mix that I’ve been using in my work for a while so I set it aside until I was ready to make that mess. ![]() When it arrived, it was a scant 3/8 of an inch and much thinner and softer than I expected. The pictures suggest that it is thick with a stack of 50 measuring maybe an inch and a half to two inches when stacked. I admit that I was a bit disappointed when the paper arrived. a substrate to spread the medium on (paper, canvas, cradle board, wood, etc.) In this case, I used some inexpensive handmade paper that I purchased on Amazon. Plaster loves to stick to wood and that can be frustrating when mixing the medium. I recommend a flexible, plastic or glass or metal container. a tool to apply the medium with like a stuff bristled brush and/or a taping knife. In this case, I usually use white gesso but clear or tinted would work similarly. The only two ingredients that you need to make this texture medium are (linked): You certainly could leave it untouched after it has dried if you wanted but because it is significantly more porous than, say, paint and baking soda, you may want to seal it with something (such as matte medium or spray fixative) to keep it from taking on finger oils and dust. It’s a prepared surface on which you can then apply so many other media. It thickens it and gives it some texture but in this case, the end result isn’t usually planned to be a finished surface. It’s not completely unlike when you see DIYers add baking soda to paint. You can shape the petals with your gloved fingers on the wax paper as needed.The first thing to know about this homemade texture medium is that it can be used on so many different surfaces and substrates. After one dip and a few minutes of drying dip a second time for full coverage. If your petals are sticking together try thinning the plaster. Lilies, orchards, and other large flowers with fewer petals are the most difficult to keep in shape. After a little practice, I would try dipping poppies, daisies, or ranunculuses. I think the easiest flower to use is a faux rose that is blush, white, or cream so the color doesn’t bleed through. I would like to know how you shaped your roses?” First, what kind of flower are you using? “I tried this and my petals collapsed and stuck together. Otherwise use a dot of hot glue in place of the plastic parts that keep the petals together. If the stem can be removed by leaving the receptacle intact then it’s ready to be dipped. “When you say remove stem and leaves, do you leave the plastic thingie attached to the flowers when you dip them? The part that holds it all together?” Yes. It’s fun to try new things! I’ve dipped faux maple leaves and they turned out lovely. “Can I plaster branches or bows?” You can dip just about anything (within reason) into plaster but keep in mind that smaller details will get lost with the plaster layers. Otherwise, wait for the plaster to dry and then paint with your choice of acrylic colors. I would use a water based craft paint to tint the plaster but only if your desire is a pastel color. “Can I tint the plaster with food coloring?” It probably wouldn’t mix well. Check out these additional tips and tricks on what you can do with plaster-dipped flowers and how to fix some common problems. I’ve gotten such a great response to this DIY and lots of good questions. Plaster cast flowers Q&A on how to make plaster flowers You may also want to separate petals on fuller flowers. I’ve seen some beautiful larger flowers turned into votive candle holders. The plaster will take 10-15 minutes to completely harden so you have time to shape the petals if you like while it is drying. Step four: Lay out the dipped flower to dry on wax paper.Shake off access plaster while you are holding it inside the container. Step three: Dip your flower, twirling it around in the plaster to completely cover it.Add a teaspoon or two more if it isn’t yogurt consistency. Stir until the lumps are out and it’s about yogurt consistency. Step two: Mix some cold water with your plaster powder using the recommended water/plaster ratio on the package.If the stem was holding the flower head together you may need a dot of hot glue to keep it together. Remove the stems and leaves from your flowers. Step one: Prepare your workspace by laying out a couple of sheets of wax paper for drying.Dip Flower Plaster of paris flower making: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |